Skip to content
365 Heat (365heat.ca)

Repair

Furnace repair in Hamilton: same-day where we can, every make and model

From a failed igniter to a seized inducer motor, we repair every make and model of gas and propane furnace. You get a straight diagnosis and a firm price before any part goes in. Same-day calls where the schedule allows across Hamilton, Stoney Creek and the surrounding communities.

The most common faults

A furnace that will not turn on is usually a hot-surface igniter, a flame sensor coated in silica, or a pressure switch tripped by a blocked condensate line. A furnace that lights and then shuts down is often an overheating limit switch caused by a clogged filter or a failing blower. Cold air from the vents, loud bangs on start-up, a burning smell, constant cycling, a thermostat that does not respond: each has a short list of causes, and we work through it methodically instead of guessing.

We carry parts for and repair Lennox, Carrier, Bryant, Trane, American Standard, Goodman, Amana, KeepRite, Rheem, York, Napoleon and the other makes found in Hamilton-area homes.

What furnace repair costs

A diagnostic visit in the Hamilton area is typically $99 to $149 and is credited against the repair when you go ahead. Common repairs, parts and labour: a hot-surface igniter $200 to $350, a flame sensor $150 to $250, a capacitor $150 to $250, a pressure switch $200 to $350, an inducer motor $450 to $800, a blower motor $500 to $950 (variable-speed ECM blowers run higher), and a control board $450 to $850. You see the exact number in writing before any part is fitted.

Repair or replace: the honest answer

A rule we follow: if the furnace is under about twelve years old and the repair is less than a third of a replacement, repair it. Over fifteen years with a major failure such as a cracked heat exchanger or a failed control board, replacement is almost always the better money. We will give you both numbers and let you decide; the reasoning is set out in repair or replace? and in how long a furnace lasts.

A cracked heat exchanger is the one fault we will not leave running. It can allow combustion gases, including carbon monoxide, into the air the furnace circulates through the house.

How a repair visit goes

We confirm the symptom with you, test the system and show you what we found. You get a written price for the repair before we start. We carry the common parts, igniters, flame sensors, capacitors, pressure switches and many control boards, on the truck, so most repairs are finished the same visit. Parts carry the manufacturer's warranty and our labour carries our own, both in writing. If the heat is out, call rather than wait.

Why call 365 Heat

Honest heating work, done by the book

  • Written price before work starts

    You see the number and approve it before any part is fitted. No surprises on the invoice.

  • A straight answer on repair or replace

    We give you both numbers and the reasoning. Plenty of furnaces that look ready to replace just need a part.

  • Clean work

    Drop cloths down, boot covers on, old equipment taken away, workspace swept before we leave.

Questions about repair

How much does furnace repair cost in Hamilton?

A diagnostic visit is typically $99 to $149 in the Hamilton area and is credited against the repair when you go ahead. Common fixes run from about $150 for a flame sensor to $950 for a blower motor. You get the exact price in writing before any part is fitted.

My furnace is running but blowing cold air. What is wrong?

Common causes are a dirty filter restricting airflow, a failed hot-surface igniter or flame sensor, a tripped limit switch from overheating, or a thermostat set to "fan on" rather than "auto". Check the filter and thermostat first; if the burner is not lighting, call for a repair. The causes in order, and what you can check yourself, are in why is my furnace blowing cold air?

Why does my furnace keep turning on and off?

Short cycling is most often an oversized furnace, a clogged filter, a faulty flame sensor or a thermostat problem. It wastes gas and wears out the igniter and blower. It is worth a service call rather than living with it.

How long does a furnace last?

A well-maintained gas furnace typically runs 15 to 20 years. A mid-efficiency unit from the 1990s is at the end of that range now, and a high-efficiency furnace installed around 2010 is approaching it. Three things shorten the life: skipped annual maintenance, an oversized unit that short-cycles, and a clogged filter that overheats the heat exchanger. Past 15 years, repairs become more frequent and parts harder to find, and a new 96 percent furnace usually pays back part of its cost in lower gas bills. The one fault that ends a furnace at any age is a cracked heat exchanger. We will tell you plainly whether a repair or a replacement makes more sense for your unit; the full reasoning is in how long does a furnace last?

All questions

Never left out in the cold.

Call for same-day service where the schedule allows, or send a message and hear back within the hour during opening hours. The price goes in writing before any work starts.